Water mains leak detection in Bridgend
Water mains leak detection finds hidden leaks in underground supply pipes using acoustic ground microphones, tracer gas and pressure testing.
Non-invasive leak detection
Acoustic, thermal and tracer gas
Trace and access claim reports
What are the signs of a water mains leak?
A meter turning with every tap off, rising bills or wet ground can indicate a leak. ADI Leak Detection Bridgend locates and marks the leak before digging begins.
A supply pipe leak is underground, so the signs below are usually all you see of it:
- The meter dial moves when every tap and appliance in the house is off
- A water bill that has climbed with no change in how much water you use
- Pressure that drops away when more than one outlet runs
- Wet ground, sinking block paving or a patch of lawn that stays green in July
- A leak notification letter from your water company through the door
If the water is going from the garden watering pipes, irrigation leak detection tests those. A falling pool level calls for swimming pool leak detection to test the pool shell and circulation pipework.
Where do water mains leaks occur in Bridgend?
The team investigates losses from incoming water supplies at the county’s named smaller settlements, including Bettws and South Cornelly.
- Describe the supply route and accessible controls, with any section serving more than one building clearly identified.
- The property’s meter position, visible damp and changes in water use help explain the suspected loss.
- Where pipes cross grounds or a shared access, tell us which parts can be reached and whether earlier plans show the concealed connection.
How does ADI Leak Detection Bridgend find a water mains leak?
The engineer isolates and pressure tests the supply pipe, listens along its route with ground microphones and confirms the leak with tracer gas before marking it. Once the position is found, the engineer explains it on site before any repair is discussed.
The pipe is usually a metre down and the sound of it travels, so tracing it first helps you avoid unnecessary digging.
Pressure testing confirms and measures water loss from the mains pipe. The engineer first isolates the supply at the boundary stop tap, then tests the pipe before tracing the leak.
Acoustic ground microphones pick up the sound of water escaping beneath the surface. The engineer moves them along the pipe route in short steps.
Hydrogen tracer gas is introduced into the isolated mains pipe and detected at the surface above the escape. The engineer uses this method where ground noise or a slab affects the search.
The water mains leak position is marked on the ground and measured back to a fixed point, so whoever digs knows where to open up.
Who fixes a leak on your supply pipe, you or the water company?
Responsibility for a supply pipe changes at the property boundary. Which water company serves your property depends on your town, and each town page names it, its leak line and its published guidance.
- Leak detection in Ogmore Vale
- Leak detection in Pontycymer
- Leak detection in Nant-y-moel
- Leak detection in Betws
- Leak detection in Blaengarw
- Leak detection in Gilfach Goch
- Leak detection in Cefn Cribwr
- Leak detection in Llangeinor
- Leak detection in Pant-yr-Awel
- Leak detection in Laleston
- Leak detection in Blackmill
- Leak detection in Heol-y-Cyw
- Leak detection in South Cornelly
What happens after a water mains leak is found?
Water mains leak repairs by ADI Leak Detection Bridgend are guaranteed. If the leak is on the water company's side of the boundary stop tap, the report identifies that so you can pass it to them.
Every leak detection visit ends with a written report by the engineer who attended, with photographs and video, formatted for trace and access and escape of water insurance claims.
- The leak position marked on site and explained before you decide anything
- Photographs and video in the written report
How do you arrange water mains leak detection in Bridgend?
Send the form with your postcode and a technical advisor will call you back, confirm the service and book the visit.
If you are unsure which investigation you need, describe what you can see when you call and the advisor will tell you.
Same or next day depending upon engineer availability.
What do people ask about water mains leak detection?
Four questions come up before a water mains survey: how long it takes, who owns the pipe, whether the driveway gets dug up and how the leak is pinpointed underground.
How long does a water mains leak detection visit take?
It depends on the property and how much of the system has to be tested, so the advisor gives you an estimate when you book.
Who is responsible for a leaking water main in Bridgend?
Your side of the boundary stop tap is yours and the street side is the water company’s; each town page names the company for that town, and the report says which side the leak is on.
Does finding a water mains leak mean digging up the driveway?
Water mains leak detection traces the pipe from the surface with acoustics, tracer gas and a pressure test. Digging happens once, at the marked point, only if you want the repair done.
What is leak noise correlation?
Leak noise correlation is a way of estimating where a leak sits on a buried pipe. Two sensors are clamped to fittings at either end of the run, the leak noise reaches each one at a slightly different moment, and the time difference gives a distance along the pipe. ADI Leak Detection Bridgend finds water mains leaks with acoustic ground microphones, tracer gas and pressure testing.
